Devices#
To perform hardware-software integration of LP5/LUNA CARS for access control, it is necessary to use devices - a terminal, cameras, etc.
All fields are required unless otherwise stated in the description.
Beward#
The biometric terminal with temperature measurement, mask detection, and built-in relay.
- Supported devices: TFR80-210T1Q / TFR80-210.
- Supported firmware versions: 1.2.13.0 / 2.1.6.0.
Beward settings#
The following settings are used when creating a new device (Table 36):
Table 34. Beward Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| successful_pass_message_template | Message on successful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Any text names and Full name variables. Only Latin characters are supported. It is not recommended to enter more than 33 characters | Welcome! |
| unsuccessful_pass_message_template | Message on unsuccessful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Any text names. Only Latin characters are supported. It is not recommended to enter more than 33 characters | Face is not identified |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the server where Beward is installed | IP address in the form of X.X.X.X or site.domain | - |
| port | Port of the server where Beward is deployed | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | Beward user login. Input of Latin characters, numbers and symbols is supported. | The user created in Beward | - |
| password | Beward user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| open_door_time | Relay closing time in milliseconds | The time is taken from the relay manual | 2000 |
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| time_change_interval | The frequency of time updates on the device. It is recommended to use it if the time on the terminal is lost. | Set in hours | 0 |
BioSmart Quasar#
- Supported devices: BioSmart Quasar.
- Supported firmware versions: 2.3.0.46.
BioSmart Quasar settings#
The following settings are used when creating a new device (Table 37):
Table 35. BioSmart Quasar Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the server where Quasar is installed | IP address in the form of X.X.X.X or site.domain | - |
| port | Port of the server where Quasar is deployed | - | 80 |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| luna_id | Drop-down list with Luna service IDs in Access | - | - |
| min_face_similarity | Minimum face similarity threshold when performing verification. | The value is formed at the design stage and corrected at the testing stage. | 0.00...1.00 |
To subscribe to events, go to “Settings” on the terminal → go to “Server Identification” → select the server type: BioSmartLite → enter the endpoint for sending data: http://server_IP/vl-access/webhook/biosmart/ → save the settings.
The device does not generate events and does not put anything in the queue. Requests to Luna are sent directly from endpoints.
Dahua#
Some models of Dahua cameras have a relay and the ability to control it programmatically.
During the implementation of the project, LP5 is integrated with this functionality, which allows to control the relay when a face from a certain list appears in the frame.
For example, it is possible to send a signal to an electronic door lock so that the door opens or does not open.
The device starts a stream connection, generates, and puts a face detection event in the queue.
Dahua settings#
The following settings are used when creating a new device (Table 38):
Table 36. Dahua settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| device_id | Internal ID of the device. Specified in the device settings | - | - |
| host | Dahua camera IP address | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to Dahua camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | Dahua user login. Input of Latin characters, numbers and symbols is supported. | The user created in Beward | - |
| password | Dahua user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
DahuaThermo#
Some models of Dahua cameras have a relay and the ability to control it programmatically.
During the implementation of the project, LP5 is integrated with this functionality, which allows to control the relay when a face from a certain list appears in the frame.
For example, it is possible to send a signal to an electronic door lock so that the door opens or does not open.
- Supported system version: 2.631.0000000.31.T, build date 2020-07-06.
The device starts an HTTP stream connection to the thermal imaging camera and captures faces by sending a thermal detection event of the face to the queue.
DahuaThermo settings#
The following settings are used when creating a new device (Table 39):
Table 37. DahuaThermo settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of Dahua Thermo camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to Dahua Thermo camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | Dahua Thermo user login. Input of Latin characters, numbers and symbols is supported. | The user created in Beward | - |
| password | Dahua Thermo user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| timeout | Timeout for an unsuccessful attempt to connect to the service. It is necessary to increase the time if there is a large delay between servers | The time is selected based on the delay in the network to maintain performance | - |
Fortuna315#
Generates Thermo events in the SendThermalEventToLuna queue based on the received data from devices. Includes paired devices — thermal imaging camera and camera.
Supported firmware versions of the camera: V4.02.00, the camera thermal imaging camera: 2.20.0.0.R26130.alpha8 V1.0. Supported hardware versions: V1.0. Supported algorithm versions: smart2.0.0-06-2020.06.17.16:06:42.
Fortuna315 settings#
To subscribe to events, create a device with the following settings (Table 40):
Table 38. Fortuna315 settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| device_id | Internal ID of the device. Specified in the device settings | - | - |
| host | IP address of Fortuna315 camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to Fortuna315 camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| thermo_host | IP address of the Fortuna315 thermal imaging camera | IP address in the form of X.X.X.X or site.domain | - |
| thermo_port | Port of the Fortuna315 thermal imaging camera | - | - |
HikvisionCamera#
A camera for generating a video stream for LP5 with subsequent integration with ACS.
- Supported devices: DS-2CD3126G2-IS.
- Supported firmware versions: V5.5.134 build 200430.
The device generates events of type FaceDetectionEvent.
HikvisionCamera settings#
To subscribe to events, create a device with the following settings (Table 41):
Table 39. HikvisionCamera Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the HikvisionCamera camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to HikvisionCamera camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | HikvisionCamera user login. Input of Latin characters, numbers and symbols is supported. | User created to access the device | - |
| password | HikvisionCamera user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| timeout | Timeout for an unsuccessful attempt to connect to the service. It is necessary to increase the time if there is a large delay between servers | The time is selected based on the delay in the network to maintain performance | 10 |
HikvisionCameraThermo#
A camera with temperature measurement and data transfer functions in LP5.
- Supported devices: DS-2CD3126G2-IS.
- Supported firmware versions: V5.5.134 build 200430.
Events in the queue are of type ThermalEvent.
HikvisionCameraThermo settings#
To subscribe to events, create a device with the following settings (Table 42):
Table 40. HikvisionCameraThermo settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the HikvisionCameraThermo camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to HikvisionCameraThermo camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | HikvisionCameraThermo user login. Input of Latin characters, numbers and symbols is supported. | User created to access the device | - |
| password | HikvisionCameraThermo user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| timeout | Timeout for an unsuccessful attempt to connect to the service. It is necessary to increase the time if there is a large delay between servers | The time is selected based on the delay in the network to maintain performance | 10 |
HikvisionRecognitionOnBoard terminal#
A biometric terminal with face recognition function.
- Supported devices: DS-K1T341AMF, DS-K1T341AM, DS-K1T680D-E1.
- Supported firmware versions: V3.2.30 build 220210.
Open the device's web interface, go to ""Configuration"" → ""Access Control"" → ""Face Recognition Parameters"" → ""Working Mode"" and make sure that the ""Permission Free Mode"" mode is set.
After adding, the faces from the specified list will be replicated to the device's memory. You can add/remove faces in Luna, the changes will be automatically applied to the device.
- the following format of the
user_datafield is required:
name;card number
- do not set or change the
external_idfield.
Updating of face data during editing is not supported. If it is necessary to update the data of a person, delete this person and add it again with the necessary data.
Events in the queue are of type FaceDetectionEvent.
HikvisionRecognitionOnBoard settings#
To subscribe to events, create a device with the following settings (Table 43):
Table 41. HikvisionRecognitionOnBoard settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the HikvisionRecognitionOnBoard camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to HikvisionRecognitionOnBoard camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | HikvisionRecognitionOnBoard user login. Input of Latin characters, numbers and symbols is supported. | User created to access the device | - |
| password | HikvisionRecognitionOnBoard user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| luna_id | Drop-down list with Luna service IDs in Access | - | - |
| recognition_interval | Interval between the start of recognition. It is set depending on the flow of people | 1...10 | 1 |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| time_change_interval | The frequency of time updates on the device. | Set in hours | 0...100 |
HikvisionTerminalThermo terminal#
The biometric terminal with temperature measurement, mask detection, and built-in relay.
Only events of the AccessControllerEvent type (having a measured temperature) will be processed, events of this type come from the terminal.
Events in the queue are of type ThermalEvent.
Hikvision terminal with temperature measurement function.
- Supported devices: DS-K1TA70MI-T, DS-K1T671TM-3XF, DS-K5671-3XF/ZU.
- Supported firmware versions: V3.2.32 build 210525.
HikvisionTerminalThermo settings#
To subscribe to events, create a device with the following settings (Table 44):
Table 42. HikvisionTerminalThermo settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| successful_pass_message | Message on successful identificationTo display the username on the terminal screen upon successful identification, you must use the special flag. The order of words in the greeting message can be any. Any text names. | Any text names and Full name variables. Only Latin characters are supported. It is not recommended to enter more than 50 characters. | Welcome |
| unsuccessful_pass_message_template | Message on unsuccessful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | It is not recommended to enter more than 50 characters | Face is not identified |
| host | IP address of the HikvisionTerminalThermo camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to HikvisionTerminalThermo camera | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | HikvisionTerminalThermo user login. Input of Latin characters, numbers and symbols is supported. | User created to access the device | - |
| password | HikvisionTerminalThermo user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| card_recognition_interval | Interval between card recognitions | 0...10 | 3 |
| face_recognition_interval | Interval between recognizing images with faces | 1...10 | 3 |
| liveness_level | Degree of checking the level of liveness | low— fast processing speed, accuracy is reduced; | low |
| middle — average processing speed and recognition accuracy; | |||
| high — accurate definition, increased resource consumption | |||
| attempts_check_liveness | Number of attempts to pass the liveness check.It is necessary to increase the number of verification attempts at complex angles and shooting conditions in order to avoid false positive recognitions | 5...15 | 10 |
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| light_brightness_led | Brightness level of the LED backlight. The darker the area in front of the terminal, the brighter the backlight should be | 0...100 | 50 |
| light_brightness_ir | Brightness level of the infrared (IR) illumination. The darker the area in front of the terminal, the brighter the illumination should be | 0...100 | 50 |
| voice_prompt | Terminal voice prompts about pass events or errors. To set up the prompts, see the official documentation of the terminal. | On/Off | Off |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| time_change_interval | The frequency of time updates on the device. | Set in hours | 0...100 |
| clear_old_events_interval | Frequency of deleting old events (in seconds), to prevent terminal memory overflow | 300...1200 | 600 |
LunaFast4A1#
The biometric terminal with recognition function.
- Supported devices: DS-K1T680D-E1, DS-K1T341AMF, DS-K1T341AM, VL LUNA FAST 4A1, VL LUNA FAST 8A1, 671, DS-K1T671M, ACT-T1341M, DS-K1T680DF-E1, DS-K5671-ZU.
- Supported firmware versions: V3.2.30 build 210415, V3.2.30 build 210525, V3.2.30 build 210526, V3.2.30 build 210812, V3.2.30 build 211025, V3.2.30 build 220607, V3.2.30 build 220803, V3.2.30 build 221027, V3.2.33 build 210816, V3.2.35 build 220415, V3.2.35 build 220817.
Events in the queue are of type FaceDetectionEvent.
To disable the output of the greeting on the terminal screen, you must disable the
LunaEventListenerpipeline.
LunaFast4A1 settings#
To subscribe to events, create a device with the following settings (Table 45):
Table 43. LunaFast4A1 Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| successful_pass_message | Message on successful identificationTo display the username on the terminal screen upon successful identification. The order of words in the greeting message can be any. Any text names. | Any text names and Full name variables. It is not recommended to enter more than 50 characters. | Welcome |
| Full name example: Welcome, {fullname}. | |||
| unsuccessful_pass_message_template | Message on unsuccessful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Only Latin characters are supported. It is not recommended to enter more than 50 characters | Face is not identified |
| host | IP address of the LunaFast4A1 camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to the LunaFast4A1 terminal | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| login | LunaFast4A1 user login. Input of Latin characters, numbers and symbols is supported. | User created to access the device | - |
| password | LunaFast4A1 user password. Input of Latin characters, numbers and symbols is supported. | User password | - |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| card_recognition_interval | Interval between card recognitions | 0...10 | 3 |
| face_recognition_interval | Interval between recognizing images with faces | 1...10 | 3 |
| liveness_level | The degree of checking the level of liveness | low— fast processing speed, accuracy is reduced; | low |
| middle — average processing speed and recognition accuracy; | |||
| high — accurate definition, increased resource consumption | |||
| attempts_check_liveness | Number of attempts to pass the liveness check.It is necessary to increase the number of verification attempts at complex angles and shooting conditions in order to avoid false positive recognitions | Values > 0 | 10 |
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| light_brightness_led | Brightness level of the LED backlight. The darker the area in front of the terminal, the brighter the backlight should be | 0...100 | 50 |
| light_brightness_ir | Brightness level of the infrared (IR) illumination. The darker the area in front of the terminal, the brighter the illumination should be | 0...100 | 50 |
| voice_prompt | Terminal voice prompts about pass events or errors. To set up the prompts, see the official documentation of the terminal. | On/Off | Off |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| time_change_interval | The frequency of time updates on the device. | Set in hours | 0...100 |
| clear_old_events_interval | Frequency of deleting old events (in seconds), to prevent terminal memory overflow | 300...1200 | 600 |
Panda#
A thermal imaging camera with face recognition.
- Supported devices: SN-T5/13, SN-F22-13.
- Supported firmware versions: v3.6.0825.1004.1.0.23.0.0, v3.6.0840.1004.1.45.1.0.2.
Events in the queue are of type ThermalEvent.
Panda settings#
To subscribe to events, create a device with the following settings (Table 46):
Table 44. Panda Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the Panda camera | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to Panda camera | - | 80 |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled |
Go to the web interface of the device → sign in → go to the “Configuration” tab → select the “Network Service” section on the left panel → go to “CGI Alarm Service Center”.
Fill in the fields in the “CGIAlarm” section: assign endpoint as URL Start and URL End to send data to Access — http://<vl_access_host>:<vl_access_port>/vl-access/webhook/device/<component_id>/event/handle_event/. If necessary, in the “Proxy Settings” section, fill in the Address and Port fields: Access host and Access port, respectively. Save settings after configuring.
R20Face terminal#
The biometric terminal with protective mask detection and centralized control.
- Supported devices: R20-Face-T8.
- Supported firmware versions: GD-V32.7267.
R20Face settings#
The following settings are used when creating a new device (Table 47):
Table 45. R20Face Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| successful_pass_message_template | Message on successful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Any text names and Full name variables. Only Latin characters are supported. It is not recommended to enter more than 33 characters | Welcome! |
| unsuccessful_pass_message | Message on unsuccessful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Any text names. Only Latin characters are supported. It is not recommended to enter more than 33 characters | Face is not identified |
| host | IP address of the server where R20Face is installed | IP address in the form of X.X.X.X or site.domain | - |
| port | Port of the server where R20Face is deployed | - | 8080 |
| password | Terminal user password | User password | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| time_zone | Time zone | -12...+12 | +3 |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| handle_detection_events | Enabling the terminal detection event processing mode | On/Off | Off |
UniUbi terminal#
The biometric terminal with temperature measurement, mask detection, and built-in relay control functions.
- Supported devices: Uface 8-C temp, Uface 8T temp, R20-Face-T8.
- Supported firmware versions: GD-V30.7219, GD-V32.7247, GD-V32.7267.
When using a terminal without measuring the temperature, you need to change the
SentThermalEventToLunapipeline toSendToLuna.
UniUbi settings#
To subscribe to events, create a device of the UniUbi type.
The following settings are used when creating a new device (Table 48):
Table 46. UniUbi Settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| handler_id | UUID of the passage event handler, created in Luna | - | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the UniUbi terminal | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to the UniUbi terminal | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| password | UniUbi user password | User password | - |
| enabled_temp_mode | Temperature measurement mode. If disabled, change the SentThermalEventToLuna pipeline to SendToLuna. |
On — enabled; | On |
| Off — disabled | |||
| vl_access_host | IP address of the server where Access is installed | IP address in the form of X.X.X.X or site.domain | - |
| vl_access_port | Port of the server where Access is deployed | - | 9091 |
| event_expiry_time | Event validity time (in seconds). It is necessary to reduce the time, with a large flow of people, as the device cache may overflow | >10 | 60 |
| time_zone | Time zone | -12...+12 | +3 |
| successful_pass_message_template | Message on successful identification. To display the username on the terminal screen upon successful identification, you must use the full name variables. The order of words in the greeting message can be any. | Any text names and Full name variables. Only Latin characters are supported. It is not recommended to enter more than 27 characters | Welcome |
| unsuccessful_pass_message | Message on unsuccessful identification | Any text names. Only Latin characters are supported. It is not recommended to enter more than 27 characters | Face is not identified |
VKVision02#
Terminal with functions of video recording and display of images on the screen.
- Supported devices: VANCOR VK VISION 02.
VKVision02 settings#
The following settings are used when creating a new device (Table 49):
Table 47. VKVision02 settings
| Parameter | Description | Values | Default value |
|---|---|---|---|
| name | Device name specified by the user | Any text names. Only Latin characters are supported. It is not recommended to enter more than 30 characters | - |
| group | List name for grouping components | Any numeric or text values | - |
| host | IP address of the VKVision01 terminal | IP address in the form of X.X.X.X or site.domain | - |
| port | Port for connecting to the VKVision01 terminal | - | - |
| enable_ssl | SSL encryption support for messages.Activate if privacy is required. When activated, the load on the device and the message transmission time increases | On — enabled; | Off |
| Off — disabled | |||
| success_status_image_ttl | Display time (ms) of the image on the terminal with the status “Success” (in seconds) | 5000...20000 | 10000 |
| success_status_image_ttl | Display time (ms) of the image on the terminal with the status “Denied” (in seconds) | 5000...20000 | 10000 |
| luna_id | Drop-down list with Luna service IDs in Access | - | - |