Skip to content

License activation using HASP key#

Note. This section describes license activation only using the HASP key. Go to the section "License activation using Guardant key" to read the corresponding instructions.

HASP key uses the "haspvlib_x86_64_30147.so" vendor library, which located in the in the /var/hasplm/ directory.

Follow these steps to set up the license:

  1. Install HASP utility on your server. HASP utility is usually installed on a separate server;
  2. Start the HASP utility;
  3. Create the fingerprint of your server and send it to VisionLabs;
  4. Activate your key, received from VisionLabs;

  5. Specify your server address. This can be done using the following methods:

    • Installation manual: in the "platform_setting.json" file before starting the LUNA PLATFORM installation or in the Configurator settings before starting the Licenses container
    • Upgrade manual: in the Configurator settings before starting the Licenses container
    • Installation using Docker Compose: in the "platform_setting.json" file before running the script

    Relevant documents contain reminders of the above actions.

The Sentinel Keys tab of the user interface (<server_host_address>:1947) shows activated keys.

Install HASP utility#

LP uses HASP utility of a certain version.

If an older version of HASP utility is installed, it is required to delete it before installation of a new version. See Delete old LP hasp utility.

Go to the HASP directory.

cd /var/lib/luna/current/extras/hasp/

Install HASP utility on you server.

yum -y install /var/lib/luna/current/extras/hasp/aksusbd-*.rpm

Launch HASP utility.

systemctl daemon-reload

systemctl start aksusbd

systemctl enable aksusbd

systemctl status aksusbd

Configure HASP utility#

You can configure the HASP utility using the /etc/hasplm/hasplm.ini file.

You do not need to perform this action if you already have the configured INI file for the HASP utility.

Delete the old file if necessary.

rm -rf /etc/hasplm/hasplm.ini

Copy the INI file with configurations. Its parameters are not described in this document.

cp /var/lib/luna/current/extras/hasp/hasplm.ini /etc/hasplm/

Add vendor library#

Copy LP vendor library (x32 and x64). This library is required for using LP license key.

cp /var/lib/luna/current/extras/hasp/haspvlib_30147.so /var/hasplm/

cp /var/lib/luna/current/extras/hasp/haspvlib_x86_64_30147.so /var/hasplm/

Restart the utility

systemctl restart aksusbd

Create fingerprint#

Go to the HASP directory.

cd /var/lib/luna/current/extras/hasp/licenseassist

Run the script 

./LicenseAssist fingerprint > fingerprint_30147.c2v

The fingerprint is saved to file "fingerprint_30147.c2v".

Send the file to VisionLabs. You license key will be created using this fingerprint.

You can also save the system fingerprint from the user interface at <host_address>:1947 by clicking the "Fingerprint" button on the "Sentinel Keys" tab.

Add license file manually using user interface#

  • Go to: <host_address>:1947 (if access is denied check your Firewall/ SELinux settings (the procedure is not described in this document));

  • Select the Update/Attach at the left pane;

  • Press the "Select File..." button and select a license file(s) in the appeared window;

  • Press the "Apply File" button.

Adding a license file
Adding a license file

Delete LP old hasp utility#

Note. Delete the HASP utility only if you need to install a newer version. Otherwise, skip this step.

Stop and disable the utility.

systemctl stop aksusbd

systemctl disable aksusbd

systemctl daemon-reload

yum -y remove aksusbd haspd